Home | Audio | DIY | Guitar | iPods | Music | Brain/Problem Solving | Links| Site Map

This work is licensed under a Creative Commons License.

DIY Tube Dampers

Build them for less than $5 each

Finshed Tube Damper

Image 1: Completed tube damper on a 6AS7 tube

There is some controversy when it comes to tube dampers; some swear by them and others think they do nothing to improve the quality of the audio at all. Personally, I realized I needed some dampers when my tubes started producing a high-frequency sound when they were on for more than an hour. The solution was obvious, but the options were not. Tube dampers will run anywhere from $10 to well over $200. The dampers that you will learn how to build below will cost around $5 each. Initially they may appear to be a bit crude, but in reality they actually are rather sharp looking and add a "retro" look to your system.


  1. Stainless Steel Hose Clamp
  2. Teflon Tubing*

*Teflon tubing may be purchased from VHAudio.com. Some may be concerned about the Teflon tubing melting. Rest assured there is no problem since Teflon melts at 640 degrees Fahrenheit and solder melts at around 400 degrees Fahrenheit. Stainless steel hose clamps are available at almost any hardware store. You may want to take measurements of your tube before heading out, or take one with you.


  1. Exacto knife
  2. Ruler--preferably metric
  3. Small slotted screw driver
  4. Paper and pencil

Tools and materials

Image 2: Tools and materials


  1. Size clamp
  2. Measure diameter of clamp
  3. Find circumference/length of tubing
  4. Cut tubing to length
  5. Slit tubing
  6. Flatten tubing
  7. Insert tubing in clamp
  8. Place clamp on tube, position the clamp and tighten
  9. Done

Before starting you may want to wipe the clamp(s) with a cloth and denatured alcohol to remove any grease or grime.

Step I

Place the clamp over the tube so that it fits loosely as in Image 3. I use the widest part of the tube for this step--an example is the tube in Image 1.

Note of Caution: The metal on the clamps can be very sharp so use care.

Size the clamp

Image 3: Sizing the clamp

Step II

Once you have sized the clamp as in Step I, the measure the diameter of the clamp. Here you want to measure the length across at the widest point. A metric ruler is far more accurate.

Measure diameter of clamp

Image 4: Measuring the diameter

Step III

Since we are placing our tubing around the inside of the clamp, then we can determine the length of the tubing by finding the circumference of the clamp. Circumference of circle = 2*Pi*radius. Since we measure the diameter then the length of tubing = Pi*diameter; where Pi=3.14. Example: Suppose the clamp has a diameter of 24 mm, then the length of the tubing will be 24 mm * 3.14 = 75.36 mm. Here I would round up to 76 mm. Below (Image 5) shows all of the steps used to find the circumference/length of the clamp (please pardon the sloppy writing.)

Circumference Formula

Image 5: Finding the circumference/length of the clamp

Step IV

Once the circumference/length of the clamp has been calculated, then measure and cut a piece of Teflon tubing of the same length.

Cut tubing

Image 6: Tubing of proper length

Step V

Once you have a piece of tubing of the correct length, then carefully make a slit down the entire length of the tubing. The objective here is to slit the tubing and then open it. When making the slit be careful not to cut through the bottom side of the tubing. You also want to make the cut as straight as possible, and watch those fingers.

Slit Tubing

Image 7: Making slit down entire length of tubing

Step VI

Once you have made a slit down the length of the tubing, then open it up and start flattening it. To flatten the Teflon you can roll it between your thumb and index finger, or while holding it fully open carefully pull the outside of the tubing over the rounded edged of a desk or table.

Flatten Tubing

Image 8: Flatten tubing

Step VII

Place the flattened piece of tubing inside of the clamp. It is easier if you place the inside of the tubing against the clamp. You may experience some frustration here, but it will work out.

Place tubing inside clamp

Image 9: Placing tubing inside clamp


Once you have placed the tubing inside of the clamp, then it is time to place the damper over the tube. Initially this can be frustrating, but once the tube has been used for a few hours then the Teflon will "settle in." Put the damper in position on the tube, and you may want to orient the screw so that it is on the backside of the tube (if tube is visible.) Once in position, then tighten the clamp being careful not to tighten it so much that you damage the tube, but tightened enough so that when the metal clamp expands with increased heat that it does not fall to the base of the tube.


Put damper on tube

Figure 10: Positioned and tightened damper


Below are a couple of images of the dampers on some E88CC's. You may want to experiment and by moving the dampers to different positions on the tube and listen for any audible changes. Enjoy.


Image 11: Tubes, beautiful tubes!

All done

Image 12: Ready for action


Home | Audio | DIY | Guitar | iPods | Music | Links | Brain and Problem Solving | Site Map | Contact


Creative Commons License